← Reading listAgendaReviewdatatracker ↗ draft-ietf-iotops-iot-dns-guidelines-06 · iotops · 22 pp · 2026-11-02 · offline copy



iotops                                                         A. Mishra
Internet-Draft                                                     Inria
Intended status: Best Current Practice                          A. Losty
Expires: 6 May 2027                                      A. M. Mandalari
                                                                     UCL
                                                               J. Mozley
                                                                Infoblox
                                                               M. Cunche
                                                       INSA-Lyon & Inria
                                                         2 November 2026


                IoT DNS Security and Privacy Guidelines
                draft-ietf-iotops-iot-dns-guidelines-06

Abstract

   This document outlines guidance for Internet of Things (IoT)
   manufacturers regarding the implementation of DNS stub resolver
   software on devices, and for the management zones used for purposes
   such as device configuration and software upgrades.  It aims to
   mitigate security threats, enhance privacy, and to address
   operational security challenges.

   DNS resolution between devices and management zone servers depends
   upon DNS services within operator networks, and these services and
   operator networks can be impacted by device behavior.  Hence, this
   document also provides guidance to network operators that deploy IoT
   devices to mitigate the specific risks identified in this document
   and take advantage of improved DNS security mechanisms provided by
   manufacturers.

About This Document

   This note is to be removed before publishing as an RFC.

   The latest revision of this draft can be found at
   https://miishra.github.io/IoT-DNS-Guidelines/draft-mishra-iotops-iot-
   dns-guidelines-latest.html.  Status information for this document may
   be found at https://datatracker.ietf.org/doc/draft-ietf-iotops-iot-
   dns-guidelines/.

   Source for this draft and an issue tracker can be found at
   https://github.com/miishra/IoT-DNS-Guidelines.







Mishra, et al.             Expires 6 May 2027                   [Page 1]

Internet-Draft             IoT-DNS-Guidelines              November 2026


Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on 6 May 2027.

Copyright Notice

   Copyright (c) 2026 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Threat Summary  . . . . . . . . . . . . . . . . . . . . .   4
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   6
   3.  Conventions and Definitions . . . . . . . . . . . . . . . . .   6
   4.  Guidance for IoT Device Manufacturers . . . . . . . . . . . .   6
     4.1.  Configuration of DNS servers used by IoT Stub
           Resolvers . . . . . . . . . . . . . . . . . . . . . . . .   7
     4.2.  Source Port and Transaction ID Randomization  . . . . . .   7
     4.3.  Handling of TTL Values  . . . . . . . . . . . . . . . . .   8
     4.4.  Support of EDNS(0)  . . . . . . . . . . . . . . . . . . .   9
     4.5.  Improve Device Behavior in Response to Resolution
           Problems  . . . . . . . . . . . . . . . . . . . . . . . .   9
     4.6.  Compliance with Encrypted DNS Standards . . . . . . . . .  10
     4.7.  Use of DNSSEC . . . . . . . . . . . . . . . . . . . . . .  10
       4.7.1.  Stub-resolver Checking for Validation . . . . . . . .  12



Mishra, et al.             Expires 6 May 2027                   [Page 2]

Internet-Draft             IoT-DNS-Guidelines              November 2026


       4.7.2.  Stub-resolver Performing Full Validation  . . . . . .  12
     4.8.  DNS over CoAP . . . . . . . . . . . . . . . . . . . . . .  13
     4.9.  Publication of Device Domain Dependencies . . . . . . . .  13
   5.  Guidance for Manufacturer Authoritative DNS Zones . . . . . .  14
     5.1.  Zone Signing  . . . . . . . . . . . . . . . . . . . . . .  14
     5.2.  TTL Values  . . . . . . . . . . . . . . . . . . . . . . .  14
   6.  Guidance for Network Operators  . . . . . . . . . . . . . . .  14
     6.1.  Resolvers Supporting DNSSEC . . . . . . . . . . . . . . .  15
     6.2.  Blocking of Unmanaged or Malicious DNS Traffic  . . . . .  15
     6.3.  Minimizing DNS Response Size  . . . . . . . . . . . . . .  15
     6.4.  Availability  . . . . . . . . . . . . . . . . . . . . . .  16
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  16
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  17
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  17
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  17
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  18
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  21
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  21

1.  Introduction

   Research into the DNS behavior of IoT devices [UCLandInriaPaper]
   shows widespread non-compliance with protocol standards, gaps in
   protocol support, and security vulnerabilities.  This leads to
   unpredictable operational behavior and exposes devices to
   fingerprinting and denial-of-service attacks.  This document provides
   DNS guidance across the IoT resolution path (device, resolver, and
   authoritative infrastructure), with primary emphasis on device
   behavior aimed at IoT manufacturers.

   The recommendations in this document are organized according to three
   roles: (1) IoT device manufacturers, concerning DNS functionality
   implemented on devices; (2) operators of authoritative DNS zones used
   for device management and related services; and (3) network operators
   providing recursive DNS resolution or DNS-based security controls to
   IoT devices.  Sections Section 4, Section 5, and Section 6 address
   these roles, respectively.  The guidance is neutral on the type of
   organization deploying DNS for IoT and leaves it up to each network
   operator to consider what is appropriate for their network
   considering the function that they want to achieve.

   While the guidance in this document may apply to any device using
   DNS, this document considers IoT devices as a specific case where
   targeted recommendations are useful for the following reasons:

   *  The recommendations address specific IoT-related security concerns
      not seen in the DNS behavior of general-purpose operating systems




Mishra, et al.             Expires 6 May 2027                   [Page 3]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   *  IoT devices have different resource characteristics from general-
      purpose devices, such as constrained power consumption, meaning
      incorrect software implementations can have an increased
      operational impact on device functionality

   *  IoT devices do not typically have endpoint security agents
      installed on them that are widely used on general-purpose
      operating systems

   *  There are many DNS RFCs, and this document can be used to identify
      those related to specific security issues observed through
      research into IoT devices, with the aim of making it easier to
      address these vulnerabilities

   *  IoT devices may be deployed at scale on dedicated networks where
      device behavior cannot be changed post-deployment, making these
      recommendations particularly useful to network security teams in
      mitigating vulnerabilities

   *  Manufacturers may use standard software distributions aimed at IoT
      devices without considering DNS behavior, and the guidelines here
      can be used as part of the criteria to evaluate these
      distributions

   *  IoT devices typically perform the same set of DNS queries on
      start-up, which makes them both more vulnerable because of this
      predictable behavior and also more prone to network fingerprinting
      [IoTDeviceIdentificationUsingPassiveNetworkTrafficAnalysis]

   This document is primarily concerned with device-to-cloud
   communication [RFC7452], but DNS may be used in other IoT device
   communication patterns.  Hence recommendations apply to any
   deployment type where DNS is used, but decisions on implementation
   will be proportionate to the associated security risks and
   operational considerations.  For example, the implementation of
   Section 4.1 and Section 4.2 would be appropriate to any
   implementation, whereas Section 4.6 may not be proportionate in
   industrial automation environments where devices do not encrypt other
   types of traffic [RFC9150].  Multicast DNS (mDNS) [RFC6762] is a
   distinct protocol from unicast DNS and is out of scope in these
   recommendations.

1.1.  Threat Summary

   Threats and associated mitigations are summarized in the table below,
   along with a link to the relevant sections.





Mishra, et al.             Expires 6 May 2027                   [Page 4]

Internet-Draft             IoT-DNS-Guidelines              November 2026


     +================+===================================+=========+
     | Threat         | Mitigation Summary                | Section |
     +================+===================================+=========+
     | Hard-coded or  | Use configurable resolvers; do    | Section |
     | ignored DNS    | not fall back to hard-coded       | 4.1     |
     | resolver       | resolvers                         |         |
     | configuration  |                                   |         |
     +----------------+-----------------------------------+---------+
     | Predictable    | Use unpredictable transaction IDs | Section |
     | source ports   | across the full 16-bit range and  | 4.2     |
     | or transaction | ensure source ports are random    |         |
     | IDs            | and span a large a range as       |         |
     |                | practical, using different source |         |
     |                | ports for concurrent queries      |         |
     +----------------+-----------------------------------+---------+
     | Excessive or   | Honor TTLs; cache responses where | Section |
     | fixed-interval | resources permit; avoid           | 4.3     |
     | queries that   | deterministic revalidation        |         |
     | ignore TTLs    | intervals                         |         |
     +----------------+-----------------------------------+---------+
     | Poor EDNS(0)   | Support EDNS(0); advertise safe   | Section |
     | support or     | UDP payload sizes to avoid        | 4.4     |
     | oversized DNS/ | fragmentation; retry over TCP     |         |
     | UDP messages   | when the TC bit is set            |         |
     +----------------+-----------------------------------+---------+
     | Retry storms   | Bound query retries; cache        | Section |
     | following      | resolution failures; use serve-   | 4.5     |
     | resolution     | stale where applicable            |         |
     | failures       |                                   |         |
     +----------------+-----------------------------------+---------+
     | Unencrypted    | Support an appropriate protected  | Section |
     | DNS traffic    | DNS transport, such as DoT, DoQ,  | 4.6     |
     |                | DoH, or protected DoC, where      |         |
     |                | feasible                          |         |
     +----------------+-----------------------------------+---------+
     | Spoofed DNS    | DNSSEC-sign manufacturer-operated | Section |
     | responses or   | management zones; rely on         | 4.7,    |
     | AiTM           | validation by a trusted resolver  | Section |
     | redirection    | or perform local DNSSEC           | 5.1     |
     |                | validation                        |         |
     +----------------+-----------------------------------+---------+
     | Compromised    | Implement ingress filtering; use  | Section |
     | devices used   | DNS Response Rate Limiting (RRL)  | 6.4     |
     | for DoS with   | where appropriate                 |         |
     | forged source  |                                   |         |
     | addresses      |                                   |         |
     +----------------+-----------------------------------+---------+




Mishra, et al.             Expires 6 May 2027                   [Page 5]

Internet-Draft             IoT-DNS-Guidelines              November 2026


                                 Table 1

2.  Terminology

   DNS terminology in this document conforms to [BCP219].

   +=============+====================================================+
   | Terminology | Description                                        |
   +=============+====================================================+
   | AiTM        | adversary-in-the-middle attacks                    |
   +-------------+----------------------------------------------------+
   | DoS         | Denial of Service                                  |
   +-------------+----------------------------------------------------+
   | Stub        | DNS resolver functionality on an IoT device that   |
   | Resolver    | relies on an upstream recursive resolver.  IoT     |
   |             | devices addressed by this document are assumed to  |
   |             | operate as stub resolvers, or local resolver       |
   |             | components that rely on an upstream recursive      |
   |             | resolver.  IoT devices operating as full recursive |
   |             | resolvers are out of scope for this document.      |
   +-------------+----------------------------------------------------+
   | Resolver    | The recursive DNS resolver used by the IoT device  |
   +-------------+----------------------------------------------------+
   | Management  | A DNS zone operated by an entity, hosting its      |
   | zone        | devices' and management servers' records           |
   +-------------+----------------------------------------------------+

                                 Table 2

3.  Conventions and Definitions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

4.  Guidance for IoT Device Manufacturers

   An IoT device may implement DNS resolution using a stub resolver, a
   validating stub resolver, or another suitable local resolver
   component.  This document does not require IoT devices to use a
   particular resolver architecture.  Unless otherwise stated, the
   recommendations in this section apply to DNS stub resolver
   functionality implemented on the device.  The following guidance
   specifies expected behavior for IoT device stub resolvers to ensure
   secure, privacy-preserving, and operationally efficient DNS
   resolution.



Mishra, et al.             Expires 6 May 2027                   [Page 6]

Internet-Draft             IoT-DNS-Guidelines              November 2026


4.1.  Configuration of DNS servers used by IoT Stub Resolvers

   IoT devices have been observed to fall back to hard-coded IP
   addresses for DNS resolvers [UCLandInriaPaper], such as well-known
   open resolvers [CharacterizingSmartHomeIoTTraffic], or ignore
   addresses assigned to them via automated configuration methods such
   as DHCP Option 6 [RFC2132].

   Such behavior can bypass network DNS policies and can prevent devices
   from functioning correctly when the hard-coded resolver is
   unreachable or blocked by the network.

   The DNS resolver configuration used by an IoT device MUST be
   configurable through applicable network configuration protocols or
   authorized device-management mechanisms.  Devices MUST NOT fall back
   to hard-coded public resolvers.

   Devices SHOULD use the following priority order for selecting a
   resolver.  The first one that results in a valid DNS response SHOULD
   be selected.

   1.  Manual user configuration.

   2.  Device management software authorized for configuration purposes.

   3.  IPv6 Router Advertisement (RA) [RFC8106], DHCPv6 [RFC9915] using
       DNS configuration options such as those defined in [RFC3646], and
       IPv4 DHCP [RFC2132].  When encrypted resolver options are present
       in DHCP or IPv6 Router Advertisements [RFC9463], they SHOULD be
       used unless the device has insufficient resources for this
       (see{#encrypted-standards}).

   If the selected resolver is identified only by an IP address and
   encrypted resolver information was not otherwise provided, Discovery
   of Designated Resolvers (DDR) [RFC9462] can be performed to discover
   an encrypted resolver, where available.

4.2.  Source Port and Transaction ID Randomization

   Some IoT devices have been observed to have insufficient or no
   randomization in the source ports of DNS queries or DNS transaction
   IDs, making them vulnerable to spoofed responses.  A combination of
   Source Port and Transaction ID is used, amongst other criteria, by
   the stub resolver when accepting a DNS response.

   Device behavior MUST be consistent with Sections 4.5 and 9.2 of
   [RFC5452].  Stub resolvers sending DNS queries over UDP MUST use
   unpredictable DNS transaction IDs across the full 16-bit range and



Mishra, et al.             Expires 6 May 2027                   [Page 7]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   unpredictable source ports selected from as large a range of
   available ports as is practical.  They MUST use multiple source ports
   when multiple DNS queries are outstanding.

4.3.  Handling of TTL Values

   IoT devices have been observed making unexpectedly high numbers of
   DNS queries even when DNS record Time-To-Live values (TTLs) would
   mean this should be unnecessary.  Devices have also been observed
   issuing DNS queries at fixed, highly predictable intervals for the
   same domain names, regardless of operational changes or TTL values.

   Unnecessary queries may lead to a drain of power in resource-
   constrained IoT devices.  Conversely, very high TTLs may impact
   device operations such as communicating with management servers,
   receiving software updates, or other changes, which may lead to
   security issues.  Deterministic query behavior that ignores TTL
   values increases the risk of device fingerprinting by adversaries who
   can profile query timing to identify specific device models or
   firmware versions.

   Manufacturers MUST configure the records in authoritative zones with
   TTL values appropriate to the use of the records by devices, ensuring
   the TTL is not too low to cause unnecessary queries for frequently
   used names, but not high enough to cause operational issues, such as
   when the IP address of an A record in a management zone changes.

   IoT device resolver implementations SHOULD cache DNS responses when
   sufficient memory and other device resources are available.
   Implementations that cache DNS resource records MUST expire, or
   otherwise process cached records in accordance with their TTLs,
   unless the device has minimum or maximum cache values configured.

   Where minimum or maximum cache TTL values are supported, these values
   SHOULD be configurable through an appropriate device-management
   mechanism rather than fixed by the implementation.  When device stub
   resolvers cannot be configured with minimum and maximum TTL values,
   this MAY be mitigated by setting these on the network resolver.

   If certain device operational requirements necessitate periodic
   revalidation of critical domains (e.g., management servers), these
   repeated queries SHOULD use non-deterministic inter-query timing to
   avoid predictable timing patterns that could enable traffic
   fingerprinting.

   In the event of resolution failure (e.g., no response from the
   resolver), devices SHOULD implement back-off strategies to limit
   unnecessary query traffic; also see Section 4.5.



Mishra, et al.             Expires 6 May 2027                   [Page 8]

Internet-Draft             IoT-DNS-Guidelines              November 2026


4.4.  Support of EDNS(0)

   Devices have been observed having limited support for EDNS(0),
   causing them to revert to TCP for queries over 512 bytes, affecting
   the device's efficiency.  Other research findings include increased
   processing overhead and devices failing to maintain their network
   connectivity when responses to DNS requests exceed 512 bytes.

   IoT devices MUST support EDNS(0) and send a supported UDP packet size
   via OPT 41 [RFC6891].  To avoid fragmentation of UDP packets, which
   may be dropped by intervening networks, manufacturers SHOULD evaluate
   guidance in [RFC9715].  Although the networks to which IoT devices
   connect may support larger packet sizes, the nature of these devices
   in being deployed on many network types, and DNS queries traversing
   networks controlled by different operators, means it is operationally
   more effective to use a smaller size that avoids fragmentation.  In
   addition, IoT devices MUST support using both TCP and UDP for
   queries, and support switching to TCP when a TC bit is returned from
   the resolver [RFC1035].

   For constrained networks where DNS messages may exceed the available
   link-layer frame size, implementors should evaluate DNS over CoAP as
   described in Section 4.8.

4.5.  Improve Device Behavior in Response to Resolution Problems

   When resolving domain names, IoT devices may not receive a response
   from a resolver.  This can result in surges in DNS queries and
   retries, or increased use of an alternative protocol (e.g., querying
   over IPv6 more frequently than over IPv4).

   Device resolver implementations MUST comply with the retry and
   resolution-failure caching requirements in Section 3.2 of [RFC9520].
   In particular, a resolver MUST NOT retry a given query to the same
   server address over the same DNS transport more than twice before
   considering that server address unresponsive for the query, and MUST
   cache resolution failures for at least one second.  Implementations
   SHOULD limit the memory and processing resources allocated to the
   resolution-failure cache to avoid performance problems.

   If supported by the stub-resolver implementation on device operating
   systems, the use of serve-stale [RFC8767] on the IoT device may
   mitigate the impact of failed resolution, such as when authoritative
   servers are unavailable.  This will reduce the impact of surges in
   DNS traffic if the network resolver is unreachable, and it may allow
   the device to maintain ongoing communication with endpoints for which
   previously valid DNS data remain usable.




Mishra, et al.             Expires 6 May 2027                   [Page 9]

Internet-Draft             IoT-DNS-Guidelines              November 2026


4.6.  Compliance with Encrypted DNS Standards

   The majority of IoT devices use unencrypted DNS over port 53, which
   means this traffic can be captured and is open to interception and
   manipulation.  Encrypted DNS protocols are not mandated for
   compliance with DNS standards, but the use of encrypted DNS may be
   mandated by some regulators and advised by competent authorities
   [ENISAGuidanceForNIS2] in deployment guidelines.  Encrypted DNS
   support is widely deployed, and it is possible for IoT devices to
   discover DNS resolver support for this as described in Section 4.1.

   IoT devices SHOULD support at least one encrypted DNS transport, such
   as DNS over TLS (DoT) [RFC7858], DNS over QUIC (DoQ) [RFC9250], or
   DNS over HTTPS (DoH) [RFC8484], when doing so is feasible and does
   not impair device operation because of power, memory, computational,
   or other deployment constraints.  This enhances privacy by preventing
   passive observation of DNS queries, improves security by mitigating
   adversary-in-the-middle (AiTM) attacks, and enables compatibility
   with resolvers that require encrypted transport.  When encrypted DNS
   is used, devices SHOULD use EDNS(0) padding as described in [RFC7830]
   and [RFC8467] to reduce size-based traffic fingerprinting, where
   doing so does not cause excessive fragmentation, energy consumption,
   or other operational costs.  Padding policies suitable for
   conventional networks may be inappropriate on constrained links with
   small frame sizes.

4.7.  Use of DNSSEC

   IoT devices can be induced to connect to an adversary's server or
   make large volumes of DNS queries via spoofed responses to queries.
   It would be difficult for manufacturers to mitigate this by
   implementing checks of data received via DNS queries, such as
   validating IP addresses in the A/AAAA record RDATA, as this does not
   reliably prevent malicious redirection.  In addition, any validation
   of this type does not address the problem of AiTM attacks targeting
   DNS query responses.

   DNSSEC can be implemented by manufacturers to mitigate AiTM attacks
   on DNS query responses.  Note that manufacturers MUST have signed
   public zones used for device management and services so that
   validation can take place.  This improves security when devices do
   not perform local validation, as many network operators deploy
   validating resolvers.

   Manufacturers MAY improve device security by utilizing DNSSEC
   validation [RFC9364] on the stub resolver.  When supported, devices
   typically follow one of two models for validation (see Table 3) by
   setting a combination of the DO and CD bits in DNS queries:



Mishra, et al.             Expires 6 May 2027                  [Page 10]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   *  Stub-resolver checking for validation - the stub resolver checks
      for the Authenticated Data (AD) bit in the response, which is
      suitable for constrained devices but requires explicit trust in
      the upstream resolver performing correct DNSSEC validation

   *  Stub-resolver performing full validation - local cryptographic
      checks of DNSSEC-related records, providing stronger assurance

   Both models improve security over unvalidated queries, but
   manufacturers should weigh the security considerations, such as trust
   assumptions, against the operational feasibility when determining
   which approach to adopt.  Manufacturers should consider the type of
   network the device is likely to be deployed on, such as a home
   network vs. other environments, in determining the likelihood of
   DNSSEC validation being available on the network and thus deciding if
   the device should rely on a validating resolver or be independently
   capable of performing DNSSEC validation.

   The deployment options are summarised below, with two constituting
   the typical deployment scenarios:

   +=====+=====+============+===========+=============================+
   |  DO |  CD |  Resolver  |   DNSSEC  | Notes                       |
   | Bit | Bit | Validated? |    RRs    |                             |
   |     |     |            | Returned? |                             |
   +=====+=====+============+===========+=============================+
   |  Y  |  Y  |     N      |     Y     | Resolver does not validate. |
   |     |     |            |           | DNSSEC data returned.       |
   |     |     |            |           | Stub-resolver performing    |
   |     |     |            |           | full validation deployment. |
   +-----+-----+------------+-----------+-----------------------------+
   |  Y  |  N  |     Y      |     Y     | Resolver validates.  DNSSEC |
   |     |     |            |           | data returned.  Stub-       |
   |     |     |            |           | resolver can use AD bit to  |
   |     |     |            |           | check validation.           |
   +-----+-----+------------+-----------+-----------------------------+
   |  N  |  Y  |     N      |     N     | Resolver does not validate. |
   |     |     |            |           | No DNSSEC data returned.    |
   |     |     |            |           | Do not use.                 |
   +-----+-----+------------+-----------+-----------------------------+
   |  N  |  N  |     Y      |     N     | Resolver validates.  No     |
   |     |     |            |           | DNSSEC data.  Stub-resolver |
   |     |     |            |           | checking for validation     |
   |     |     |            |           | deployment.                 |
   +-----+-----+------------+-----------+-----------------------------+

                Table 3: Stub-resolver deployment options




Mishra, et al.             Expires 6 May 2027                  [Page 11]

Internet-Draft             IoT-DNS-Guidelines              November 2026


4.7.1.  Stub-resolver Checking for Validation

   Where a manufacturer implements DNSSEC validation on the device, the
   minimum implementation will be a stub resolver checking the AD bit to
   see if the answer has been validated.  Relying solely on the AD bit
   assumes that the upstream resolver is trustworthy and uncompromised.

   Manufacturers may implement a testing mechanism to determine if the
   network resolver supports DNSSEC, enabling the device to utilize
   validation when available in a network that supports it, or falls
   back to unvalidated answers.  Any such test of the resolver will only
   validate that it supports DNSSEC; given that the resolver is
   performing the validation, it must be explicitly trusted.

   To determine whether a DNS response has been validated, a stub
   resolver MUST check the Authenticated Data (AD) bit [RFC4035] in
   responses to determine whether data was validated by the resolver it
   is using.  When checking for the AD bit, stub resolvers MUST treat
   DNSSEC validation failures as fatal.  Responses that fail validation
   MUST NOT be used for name resolution.

4.7.2.  Stub-resolver Performing Full Validation

   A device stub resolver MAY perform DNSSEC validation locally when the
   network resolver does not perform validation or when the device does
   not trust the network resolver to do so.  Local validation introduces
   additional implementation, processing, memory, and trust-anchor-
   management requirements that manufacturers need to consider for
   constrained devices.

   Considerations for device manufacturers in implementing full
   validation include:

   *  Devices performing local validation gain end-to-end trust but at a
      higher computational cost

   *  Devices should cache results, including validation outcomes, to
      reduce repeated computation

   *  Devices need to be shipped with a root trust anchor and have a
      mechanism to update this securely

   IoT devices that perform local DNSSEC validation MUST conform to the
   applicable DNSSEC validation requirements in [RFC4035].
   Manufacturers may implement this functionality in a validating stub
   resolver, a local validating resolver, or another suitable local
   resolver component.




Mishra, et al.             Expires 6 May 2027                  [Page 12]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   Devices performing local DNSSEC validation MUST maintain
   authenticated DNS trust anchors and MUST provide a secure mechanism
   to provision and update them.  Manufacturers SHOULD support automated
   trust-anchor updates as described in [RFC5011] or provide these
   through an alternative mechanism such as device updates, and MUST
   support changes to DNSSEC cryptographic algorithms through device
   updates.  Device software updates MAY include changes to the CA root
   store to support the TLS used in Encrypted DNS protocols.

4.8.  DNS over CoAP

   DNS over CoAP (DoC) [RFC9953] provides a DNS transport for
   constrained IoT environments using CoAP [RFC7252], with
   confidentiality and integrity provided by (D)TLS or OSCORE [RFC8613].
   DoC is appropriate where the resource or transport characteristics of
   constrained devices make DoT, DoH, or DoQ unsuitable.  The choice of
   DNS transport should consider device resources, available protocol
   stacks, network characteristics, and operational requirements.

   Implementations MUST conform to all requirements specified in
   [RFC9953], these include resolver configuration, request/response
   matching, caching, retransmission, and security.  Implementations
   MUST additionally follow [RFC7252] and [RFC7959] where requirements
   interact with the underlying CoAP transport.

   Implementations where traffic analysis is a concern should consider
   message size, timing, and packet-count characteristics when selecting
   DoC block sizes, padding, and header-compression mechanisms.
   Mitigations including block-size selection and final-block padding
   are discussed in [RFC9953] and [LendersDoCPrivacy]; SCHC [RFC8724]
   MAY additionally be used to reduce observable header information.

4.9.  Publication of Device Domain Dependencies

   To allow network operators to distinguish legitimate device traffic
   from anomalous or malicious traffic, manufacturers SHOULD provide
   network operators with accurate and current information about the
   domain names, domain-name patterns, and external services required
   for device operation.  When providing details of the domains used by
   a device for network security, manufacturers SHOULD include all such
   domains, including those outside their direct control, such as
   content delivery networks or cloud services.

   Manufacturer Usage Descriptions (MUDs) [RFC8520] can provide machine-
   readable information that defines the network communications required
   for device operation and can support the deployment of network
   security controls.  Manufacturers SHOULD publish device communication
   requirements, including relevant management domain names, in a



Mishra, et al.             Expires 6 May 2027                  [Page 13]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   publicly retrievable MUD file [RFC8520], or in comparable
   manufacturer documentation if MUD files are not supported for the
   device.

   Manufacturers SHOULD update this information when device dependencies
   change so that device operations are not impacted.

5.  Guidance for Manufacturer Authoritative DNS Zones

   Manufacturers use public authoritative DNS zones for purposes such as
   device configuration, control, and upgrades.  This section covers
   guidance for manufacturers in operating these zones.

5.1.  Zone Signing

   Zones supporting the management and data collection of devices MUST
   be DNSSEC signed in order to support the behavior described in
   Section 4.7 and Section 6.1.  The zones used for these purposes
   should be publicly listed for network operators to use in securing
   their networks as described in Section 6.2.

5.2.  TTL Values

   As stated in Section 4.3, manufacturers MUST configure TTL values for
   management zone records that are appropriate for device operations,
   considering a balance between avoiding excessive query traffic,
   maintaining continuous operation in the event the resolver is
   unreachable, and accommodating potential changes in RDATA such as
   management IP addresses.

6.  Guidance for Network Operators

   This section provides guidance to operators that have IoT devices on
   their networks.  Manufacturers should be aware of the network
   operator guidance in this section as devices will use these
   resolvers, even though this infrastructure is not under the
   manufacturer's control.

   Most IoT devices do not have dedicated security software agents, as
   are commonly available for general-purpose operating systems.  In
   addition, supply chain vulnerabilities may result in devices being
   compromised before they reach the consumer.  Network operators can
   use DNS resolvers to mitigate these risks, although this will vary
   depending on policy.  These networks may be public, without
   restrictions on DNS usage, or may be private networks that could be
   dedicated to IoT devices where operators implement more security
   controls to mitigate these risks.




Mishra, et al.             Expires 6 May 2027                  [Page 14]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   Some aspects of DNS security rely on the resolution process between
   stub resolver, resolver, and authoritative servers, as well as DNS
   record types (notably DNSSEC).  It is therefore necessary for network
   operators to implement DNS in such a way as to support some of the
   recommendations in Section 4.

6.1.  Resolvers Supporting DNSSEC

   In order to support improving device DNS security as described in
   Section 4.7, resolvers SHOULD be configured to validate DNS responses
   using DNSSEC.

6.2.  Blocking of Unmanaged or Malicious DNS Traffic

   Private network operators may block DNS traffic to resolvers not
   managed by the operator to prevent bypass of DNS security controls,
   such as Response Policy Zones (RPZs) and DNS traffic logging.  This
   practice is more common on enterprise and other private networks than
   on service-provider networks, where operators may avoid restricting
   customers' use of alternative resolvers.

   Where operators maintain networks dedicated to IoT devices, they MAY
   restrict DNS resolution to domain names that are necessary for normal
   device operation in order to reduce the impact of a device
   compromise.

   Network operators MAY use manufacturer-provided domain dependency
   information, including MUDs [RFC8520], to distinguish legitimate
   device traffic from anomalous or malicious traffic.

6.3.  Minimizing DNS Response Size

   Recursive resolvers serving constrained IoT networks SHOULD minimize
   unnecessary DNS response data where supported by the resolver
   implementation, unless it impacts the operation of other types of
   devices on the network.  In particular, operators SHOULD use minimal-
   response configurations that avoid unnecessary Additional-section
   records while retaining records required for correct DNS resolution
   and the semantics of the queried RR type [RFC9715].

   Reducing unnecessary response data can reduce bandwidth usage,
   processing overhead, energy consumption, and the likelihood of
   fragmentation on constrained links.








Mishra, et al.             Expires 6 May 2027                  [Page 15]

Internet-Draft             IoT-DNS-Guidelines              November 2026


6.4.  Availability

   Providers should optimize resolver configurations to mitigate the
   security and operational risks identified in this document, provided
   that such optimizations do not adversely affect the operation of
   other DNS clients.

   Network operators SHOULD optimize DNS resolver configurations through
   the use of serve-stale mechanisms, as specified in [RFC8767].  In
   particularly this is RECOMMENDED in environments dedicated to
   supporting IoT devices, in order to minimize operational disruption
   during DNS resolution failures.  Recursive DNS resolvers provided to
   IoT devices SHOULD be able to perform dual-stack DNS resolution,
   consistent with [RFC10001], to support both IPv4 and IPv6 networks.

   DNS queries are most commonly transported over UDP, and compromised
   devices have been used to launch DoS attacks by sending queries with
   forged source addresses.  Therefore, network operators MUST implement
   [RFC2827] network ingress filtering.  Network operators SHOULD
   implement DNS Response Rate Limiting (RRL) on resolvers to mitigate
   high query volumes from devices causing DoS attacks against DNS
   infrastructure.

7.  Security Considerations

   IoT devices are often deployed at scale, operate under resource
   constraints, and typically lack host-based security controls.
   Consequently, weaknesses in DNS behavior can increase exposure to
   spoofing, on-path attacks, amplification, and fingerprinting.  The
   guidance in this document improves the security properties of DNS
   resolution by promoting correct protocol behavior, reducing
   unnecessary or anomalous query traffic, and supporting the use of
   authenticated and integrity-protected data (e.g., DNSSEC) and
   encrypted transport.  The effectiveness of these measures depends on
   coordinated deployment across stub resolvers, recursive resolvers,
   and authoritative servers.  Partial deployment may reduce the
   benefits of some mechanisms.

   Residual risks remain, including device compromise outside the DNS
   layer, misconfiguration, and reliance on untrusted upstream
   resolvers.  In addition, the use of encrypted DNS may limit network-
   based inspection and policy enforcement.  This document does not
   introduce new protocols or mechanisms; it reduces the attack surface
   and improves the predictability and resilience of DNS interactions in
   IoT environments.






Mishra, et al.             Expires 6 May 2027                  [Page 16]

Internet-Draft             IoT-DNS-Guidelines              November 2026


8.  IANA Considerations

   This document has no IANA actions.

9.  References

9.1.  Normative References

   [RFC1035]  Mockapetris, P., "Domain names - implementation and
              specification", STD 13, RFC 1035, DOI 10.17487/RFC1035,
              November 1987, <https://www.rfc-editor.org/rfc/rfc1035>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/rfc/rfc2119>.

   [RFC2827]  Ferguson, P. and D. Senie, "Network Ingress Filtering:
              Defeating Denial of Service Attacks which employ IP Source
              Address Spoofing", BCP 38, RFC 2827, DOI 10.17487/RFC2827,
              May 2000, <https://www.rfc-editor.org/rfc/rfc2827>.

   [RFC5452]  Hubert, A. and R. van Mook, "Measures for Making DNS More
              Resilient against Forged Answers", RFC 5452,
              DOI 10.17487/RFC5452, January 2009,
              <https://www.rfc-editor.org/rfc/rfc5452>.

   [RFC6891]  Damas, J., Graff, M., and P. Vixie, "Extension Mechanisms
              for DNS (EDNS(0))", STD 75, RFC 6891,
              DOI 10.17487/RFC6891, April 2013,
              <https://www.rfc-editor.org/rfc/rfc6891>.

   [RFC7252]  Shelby, Z., Hartke, K., and C. Bormann, "The Constrained
              Application Protocol (CoAP)", RFC 7252,
              DOI 10.17487/RFC7252, June 2014,
              <https://www.rfc-editor.org/rfc/rfc7252>.

   [RFC7959]  Bormann, C. and Z. Shelby, Ed., "Block-Wise Transfers in
              the Constrained Application Protocol (CoAP)", RFC 7959,
              DOI 10.17487/RFC7959, August 2016,
              <https://www.rfc-editor.org/rfc/rfc7959>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.






Mishra, et al.             Expires 6 May 2027                  [Page 17]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   [RFC9520]  Wessels, D., Carroll, W., and M. Thomas, "Negative Caching
              of DNS Resolution Failures", RFC 9520,
              DOI 10.17487/RFC9520, December 2023,
              <https://www.rfc-editor.org/rfc/rfc9520>.

   [RFC9715]  Fujiwara, K. and P. Vixie, "IP Fragmentation Avoidance in
              DNS over UDP", RFC 9715, DOI 10.17487/RFC9715, January
              2025, <https://www.rfc-editor.org/rfc/rfc9715>.

   [RFC9953]  Lenders, M. S., Amsüss, C., Gündoğan, C., Schmidt, T. C.,
              and M. Wählisch, "DNS over CoAP (DoC)", RFC 9953,
              DOI 10.17487/RFC9953, March 2026,
              <https://www.rfc-editor.org/rfc/rfc9953>.

9.2.  Informative References

   [BCP219]   Best Current Practice 219,
              <https://www.rfc-editor.org/info/bcp219>.
              At the time of writing, this BCP comprises the following:

              Hoffman, P. and K. Fujiwara, "DNS Terminology", BCP 219,
              RFC 9499, DOI 10.17487/RFC9499, March 2024,
              <https://www.rfc-editor.org/info/rfc9499>.

   [CharacterizingSmartHomeIoTTraffic]
              "Characterizing smart home IoT traffic in the wild", n.d.,
              <https://ieeexplore.ieee.org/abstract/document/9097598>.

   [ENISAGuidanceForNIS2]
              "NIS2 Technical Implementation Guidance", n.d.,
              <https://www.enisa.europa.eu/publications/nis2-technical-
              implementation-guidance>.

   [IoTDeviceIdentificationUsingPassiveNetworkTrafficAnalysis]
              "Early-Stage IoT Device Identification Using Passive
              Network Traffic Analysis", n.d.,
              <https://ieeexplore.ieee.org/abstract/document/11579207>.

   [LendersDoCPrivacy]
              "Secrets Best Not Shared - DNS Privacy Enhancements for
              the Constrained IoT", n.d.,
              <https://doi.org/10.1109/EuroSP68448.2026.00094>.

   [RFC2132]  Alexander, S. and R. Droms, "DHCP Options and BOOTP Vendor
              Extensions", RFC 2132, DOI 10.17487/RFC2132, March 1997,
              <https://www.rfc-editor.org/rfc/rfc2132>.





Mishra, et al.             Expires 6 May 2027                  [Page 18]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   [RFC3646]  Droms, R., Ed., "DNS Configuration options for Dynamic
              Host Configuration Protocol for IPv6 (DHCPv6)", RFC 3646,
              DOI 10.17487/RFC3646, December 2003,
              <https://www.rfc-editor.org/rfc/rfc3646>.

   [RFC4035]  Arends, R., Austein, R., Larson, M., Massey, D., and S.
              Rose, "Protocol Modifications for the DNS Security
              Extensions", RFC 4035, DOI 10.17487/RFC4035, March 2005,
              <https://www.rfc-editor.org/rfc/rfc4035>.

   [RFC5011]  StJohns, M., "Automated Updates of DNS Security (DNSSEC)
              Trust Anchors", STD 74, RFC 5011, DOI 10.17487/RFC5011,
              September 2007, <https://www.rfc-editor.org/rfc/rfc5011>.

   [RFC6762]  Cheshire, S. and M. Krochmal, "Multicast DNS", RFC 6762,
              DOI 10.17487/RFC6762, February 2013,
              <https://www.rfc-editor.org/rfc/rfc6762>.

   [RFC7452]  Tschofenig, H., Arkko, J., Thaler, D., and D. McPherson,
              "Architectural Considerations in Smart Object Networking",
              RFC 7452, DOI 10.17487/RFC7452, March 2015,
              <https://www.rfc-editor.org/rfc/rfc7452>.

   [RFC7830]  Mayrhofer, A., "The EDNS(0) Padding Option", RFC 7830,
              DOI 10.17487/RFC7830, May 2016,
              <https://www.rfc-editor.org/rfc/rfc7830>.

   [RFC7858]  Hu, Z., Zhu, L., Heidemann, J., Mankin, A., Wessels, D.,
              and P. Hoffman, "Specification for DNS over Transport
              Layer Security (TLS)", RFC 7858, DOI 10.17487/RFC7858, May
              2016, <https://www.rfc-editor.org/rfc/rfc7858>.

   [RFC8106]  Jeong, J., Park, S., Beloeil, L., and S. Madanapalli,
              "IPv6 Router Advertisement Options for DNS Configuration",
              RFC 8106, DOI 10.17487/RFC8106, March 2017,
              <https://www.rfc-editor.org/rfc/rfc8106>.

   [RFC8467]  Mayrhofer, A., "Padding Policies for Extension Mechanisms
              for DNS (EDNS(0))", RFC 8467, DOI 10.17487/RFC8467,
              October 2018, <https://www.rfc-editor.org/rfc/rfc8467>.

   [RFC8484]  Hoffman, P. and P. McManus, "DNS Queries over HTTPS
              (DoH)", RFC 8484, DOI 10.17487/RFC8484, October 2018,
              <https://www.rfc-editor.org/rfc/rfc8484>.







Mishra, et al.             Expires 6 May 2027                  [Page 19]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   [RFC8520]  Lear, E., Droms, R., and D. Romascanu, "Manufacturer Usage
              Description Specification", RFC 8520,
              DOI 10.17487/RFC8520, March 2019,
              <https://www.rfc-editor.org/rfc/rfc8520>.

   [RFC8613]  Selander, G., Mattsson, J., Palombini, F., and L. Seitz,
              "Object Security for Constrained RESTful Environments
              (OSCORE)", RFC 8613, DOI 10.17487/RFC8613, July 2019,
              <https://www.rfc-editor.org/rfc/rfc8613>.

   [RFC8724]  Minaburo, A., Toutain, L., Gomez, C., Barthel, D., and JC.
              Zuniga, "SCHC: Generic Framework for Static Context Header
              Compression and Fragmentation", RFC 8724,
              DOI 10.17487/RFC8724, April 2020,
              <https://www.rfc-editor.org/rfc/rfc8724>.

   [RFC8767]  Lawrence, D., Kumari, W., and P. Sood, "Serving Stale Data
              to Improve DNS Resiliency", RFC 8767,
              DOI 10.17487/RFC8767, March 2020,
              <https://www.rfc-editor.org/rfc/rfc8767>.

   [RFC9150]  Cam-Winget, N. and J. Visoky, "TLS 1.3 Authentication and
              Integrity-Only Cipher Suites", RFC 9150,
              DOI 10.17487/RFC9150, April 2022,
              <https://www.rfc-editor.org/rfc/rfc9150>.

   [RFC9250]  Huitema, C., Dickinson, S., and A. Mankin, "DNS over
              Dedicated QUIC Connections", RFC 9250,
              DOI 10.17487/RFC9250, May 2022,
              <https://www.rfc-editor.org/rfc/rfc9250>.

   [RFC9364]  Hoffman, P., "DNS Security Extensions (DNSSEC)", BCP 237,
              RFC 9364, DOI 10.17487/RFC9364, February 2023,
              <https://www.rfc-editor.org/rfc/rfc9364>.

   [RFC9462]  Pauly, T., Kinnear, E., Wood, C. A., McManus, P., and T.
              Jensen, "Discovery of Designated Resolvers", RFC 9462,
              DOI 10.17487/RFC9462, November 2023,
              <https://www.rfc-editor.org/rfc/rfc9462>.

   [RFC9463]  Boucadair, M., Ed., Reddy.K, T., Ed., Wing, D., Cook, N.,
              and T. Jensen, "DHCP and Router Advertisement Options for
              the Discovery of Network-designated Resolvers (DNR)",
              RFC 9463, DOI 10.17487/RFC9463, November 2023,
              <https://www.rfc-editor.org/rfc/rfc9463>.






Mishra, et al.             Expires 6 May 2027                  [Page 20]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   [RFC9915]  Mrugalski, T., Volz, B., Richardson, M., Jiang, S., and T.
              Winters, "Dynamic Host Configuration Protocol for IPv6
              (DHCPv6)", STD 102, RFC 9915, DOI 10.17487/RFC9915,
              January 2026, <https://www.rfc-editor.org/rfc/rfc9915>.

   [RFC10001] Momoka and T. Fiebig, "Operational Guidelines for DNS
              Transport in Mixed IPv4/IPv6 Environments", BCP 91,
              RFC 10001, DOI 10.17487/RFC10001, August 2026,
              <https://www.rfc-editor.org/rfc/rfc10001>.

   [UCLandInriaPaper]
              "From Lookup to Lockdown DNS Guidelines for Securing IoT
              Ecosystems", n.d.,
              <https://discovery.ucl.ac.uk/id/eprint/10223583/>.

Acknowledgments

   We thank the researchers, reviewers, and engineers who contributed to
   the analysis and testing process.

   The authors thank Lou Berger, Henk Birkholz, Mohamed Boucadair, Chris
   Box, Stephen Farrell, Ross Gibson, Eliot Lear, Martine Lenders,
   Alexey Melnikov, Patrick Mevzek, Jim Reid, Michael Richardson and
   Hannes Tschofenig for their contributions, questions and comments.

Authors' Addresses

   Abhishek Mishra
   Inria
   Email: abhishek.mishra@inria.fr


   Andrew Losty
   UCL
   Email: andrew.losty.23@ucl.ac.uk


   Anna Maria Mandalari
   UCL
   Email: a.mandalari@ucl.ac.uk


   Jim Mozley
   Infoblox
   Email: jmozley@infoblox.com






Mishra, et al.             Expires 6 May 2027                  [Page 21]

Internet-Draft             IoT-DNS-Guidelines              November 2026


   Mathieu Cunche
   INSA-Lyon & Inria
   Email: mathieu.cunche@inria.fr
















































Mishra, et al.             Expires 6 May 2027                  [Page 22]